Topcon 3D-MC2 Dozer Grader Machine Control Kit

Topcon 3D-MC2 Dozer Grader Machine Control Kit for sale. Setup is in good shape and ready to be installed and go to work with Grader, Dozer. Kit includes Topcon GX-55, MC-R3 and Digital UHF II 450-470 MHz Radio, PG-S3 Antenna and T-Mesh Modem with 2 Connectors.

The GX-55 3D Control box has the 3 machine options enabled. The MC-R3 Dual mag box has the MC2 boards and Digital UHF II 450-470 MHz Radio. Work with most Topcon Base and Rover Kit operating at the same frequency.

This kit includes everything needed to install Machine Control on a Topcon wired Dozer, Grader. All gears has completed a thorough tested, serviced and precisely calibrated by Topcon authorized, all firmware updated, sold as is with 6-Month warranty and 30-Day monay back guarantee.

Purchased new from Topcon in 2018 and comprise of the following items:

• Topcon GX-SS, Serial No: 1446-xxxxx
• Topcon PG-53 with Pole Mount - Serial No: 1059-xxxxx
• Topcon MC-R3 Single 112 DIGV - Serial No: 1172-xxxxx
• Topcon MC-R3 GGD Full MC Sing - Serial No: 1172-xxxxx
• Topcon GX-55 3D Grader only - Serial No: 1446-xxxxx
• T-Mesh Modem with 2 Connectors - Serial No: 388-xxxx With Carry Case
• Mounting Pole - Adjustable

TOPCON 3D-MC2 MACHINE CONTROL KIT

Topcon MC-R3 is the heart of Topcon's 3D GPS+ system. The MC-R3 contains all receivers, radios, and controllers in a single tough housing. A built-in MINTER panel provides status lights and function keys for easy performance verification and system checks. The MC-R3 also features an ethernet port, robust processing power, and additional valve drivers for the widest array of machine compatibility.

Shatter the Final 3D Automation Production Barrier – Speed
Traditional finish grading with a dozer took multiple passes at slower speeds. Existing 3D-GPS machine control allowed operators to double their production. 3D-MC2 uses revolutionary technology to reach an unbelievable new level of performance: four times faster than a standard dozer, two times faster than any 3D dozer! One dozer doing the work of two 3D dozers; think of the money you will save.

More Efficient Use of your Machine
3D-MC2 will drastically change the role your dozer plays on a typical job site, in some cases it may even replace the need for a motor grader. It also means more efficient use of your dozer. Not only does speed increase, but fewer passes are needed, so more work can be done in less time. That means less machine operating time translating into less fuel, less wear on a machine and most importantly, more time that can be spent working in other areas or jobsites.

Improved Operator Performance
3D-MC2 is built on our same easy to use interface so your operators will have no problem putting it to work right away. As a matter of fact, with the advancements of 3D-MC2 your less experienced operators will be able to compete with even your most skilled operators. More for less, what could be better!

How it Works
3D-MC2 utilizes our Topcon’s GX-60 control box, GPS+ antenna, MC-R3 receiver and MC2 sensor and pairs them with advanced controlling software to provide position updates up to 100 times per second. The MC2 sensor combines a gyro, compass and inertial sensor to measure the X, Y and Z position as well as the roll, pitch, yaw and acceleration of the dozer. 3D-MC2 provides the most stable and responsive control system possible

The Topcon 3D-MC2 Advantage
Fine grading with a dozer has been typically done in first gear. Not anymore. Now you can move more material at higher speeds and at a tighter accuracy with one machine. That’s the Topcon advantage.

Features:

• Increase speeds up to 200% over existing 3D systems
• Smoothness and grading accuracy comparable to motor graders
• Same easy-to-use interface as previous Topcon machine automation systems
• Unmatched productivity that you will have to see to believe!